PerformancePro Pumps · Hillsboro, Oregon, USA

VAH Series

Aquaculture · Variable speed · Models: A13-4600-7S-T9H6B, A15-4910-7S-T9K6D

Spec page · Performance curves · Manual (PDF)

Duty table

Head in feet of water and power in watts at each flow, read from the published curves (water, 60 Hz), every 10 GPM. Full-speed values. These pumps also run slower, covering any point below the full-speed curve; the selector gives speed and watts for a specific point. A blank cell is past that model's maximum flow. Exact values for any point: https://performancepropumps.com/api/selector?gpm=…&head=…

Flow (GPM)	A13-4600-7S-T9H6B		A15-4910-7S-T9K6D
Flow (GPM)	Head (FT)	Power (W)	Head (FT)	Power (W)
0	72.5	823	84.8	992
10	72.6	934	85.5	1135
20	71.9	1044	85.6	1280
30	70.4	1149	85.2	1424
40	68.1	1249	84.3	1566
50	65.2	1337	82.9	1702
60	61.5	1413	80.9	1833
70	57.0	1473	78.5	1954
80	51.9	1513	75.6	2066
90	46.0	1531	72.1	2165
100	39.5	1524	68.3	2250
110	32.2	1488	63.9	2319
120	24.2	1421	59.0	2370
130	15.6	1319	53.8	2401
140			48.0	2410
150			41.8	2396
160			35.2	2355
170			28.1	2288
180			20.6	2190

Maximum flow (GPM): A13-4600-7S-T9H6B 138, A15-4910-7S-T9K6D 187

Specifications

Spec	A13-4600-7S-T9H6B	A15-4910-7S-T9K6D
Design type	self prime	self prime
Max flow (GPM)	138	187
Max head (FT)	72.5	84.8
Max power (W)	1530	2410
Impeller number	A1H	A2H
Trim (IN)	4.6	4.91
Motor power (HP)	1.65	2.7
Enclosure	TEFC	TEFC
Speed (RPM)	3450-1725	3450-1725
Low volts (V)	115	-
Low volt amps (A)	13.6	-
High volts (V)	230	230
High volt amps (A)	6.8	11.1
Frequency (HZ)	variable	variable
Phase	1	1
Inverter capable	on board	on board
Weight (LBS)	38.8	43.8
Height (IN)	13.5	13.5
Length (IN)	25.82	25.82
Width (IN)	11.25	11.25
Port (IN)	2	2
Housing material	PP	PP
Seal material	SiC/SiC	SiC/SiC
Tested fluid	H2O	H2O
Datasheet	PDF	PDF

Limits

Results are a curve-coverage screen, not a final selection. Confirm the choice against the datasheet and the installation before ordering.
Curves are for water at 60 Hz. Salt water, other fluids, temperature, and 50 Hz supply are not considered.
NPSH and suction conditions are not checked.
Suction lift is not checked. A self-priming model is not confirmed to prime at any particular lift.
The system curve is assumed to be head = static + k * gpm^2 through the single design point given. Real piping, filters, and backwash duty are not modeled.
Motor voltage, phase, and enclosure are not matched to the site. See the spec rows for each model.
Variable-speed speed and watts are affinity-law estimates.